Education

01

Online Course

All the necessary information to smoothly transition to Augma bone cement.

Read More
02

Webinars

Watch ABCA webinars and get complementary CE credits.
 
 
Read More
03

Protocols 

Learn the protocols that are changing the concept of traditional bone grafting.
 
Read More
04

Clinical Cases

A range of clinical cases by ABCA Bone Cement Experts. Sinus Lift, Lateral Augmentation, Socket Grafting, and more.

Read More
05

Clinical Support

Fill up the clinical case support form and one of ABCA Bone Cement Experts will contact you shortly 

 

Read More
06

Clinical Literature

Clinical Literature

Review, critical assessment and evaluation of research studies on Bone Cement.

Read More
07

BCS

Biphasic Calcium Sulfate as 2nd generation technological breakthrough in the long history of CS bone regeneration

Read More
08

FAQ

Do you have a question about Bone Cements? your answer is probably here.
 
 
Read More
09

The Logic Behind

Why flap with tension? Why no membranes? How come maximal closure is acceptable?                                                                               

Read More

Intro Course

Free
bond

Augma Bond Apatite® Intro Course

The course is aimed to provide all the necessary information to smoothly transition to Augma bone cement from traditional grafting and shorten the learning curve to minimal.

*US CLINICIANS EARN 0.5 CE*

Enroll Now

Webinars

Free

Dr. Stéphane Berg – Sinus Lift – 1 CE

See more...

0% Complete
0/2 Steps

Free

Dr. Amos Yahav – Lateral Ridge Augmentation – 2 CE

See more...

0% Complete
0/2 Steps

Free

Dr. Amos Yahav – Socket Preservation – 1 CE

See more...

0% Complete
0/2 Steps


All Webinars

Clinical Cases

All Clinical Cases

FAQ

Will Augma stabilize implants placed with crestal residual bone, since it is a cement?

The initial stability for any implant is due to placement in the residual bone. The purpose of bone graft cement is to regenerate bone around the implant. It has no continuous cementing properties. Bond Apatite has bioactive properties to regenerate bone.

What is biphasic calcium sulfate and why is it different from the old known calcium sulfate?

Biphasic calcium sulfate is a patented formulation of calcium sulfate. This is the only formulation of calcium sulfate that has the ability to behave as a cement in the oral cavity. Additionally, the BCS is moldable and can set and harden instantly in the presence of blood and saliva. The old calcium sulfate could not set and harden when it got it to contact with blood or saliva; therefore, it could not be easily used as a suitable cement in the maxillofacial field.

What is the working time with Bond Apatite®?

The working time with Bond Apatite® starts when the powder is mixed with saline by advancing the plunger in the smart syringe and introducing the saline in to the premeasured BCS/HA powder chamber. At this time, the material is moldable and pliable. The best pliability is seen immediately after cement activation. Thus, it is vital to have the host site completely prepared before the activation of Bond Apatite®. After the site has been prepared, activate the cement within its smart syringe and eject it into the site. As soon as Bond Apatite® is placed in the site, it should be compressed with a dry sterile gauze pad for 3 seconds, and then the material hardens in situ immediately. The compression should be done by applying finger pressure on the gauze for 3 seconds, followed by an additional few seconds' compactions with a periosteal elevator on the gauze. Once completed, remove the gauze and continue with soft tissue closure according to the protocols.

How long does it take for Bond Apatite® to harden?

In the oral cavity, pressing with gauze for 3 seconds generates an instant primary setting. In vitro hardening takes approximately 3-5 minutes.

As can be seen in the protocols, it is recommended to activate the cement within its smart syringe after complete site preparation, injec the cement directly into the site, and immediately place a dry sterile gauze pad above and press with a finger on top for 3 seconds. This should be followed by an additional few seconds' pressure on the gauze with a periosteal elevator.

Does Bond Apatite® remain hard during the healing period?

The material does not remain hard. The resorbtion process begins immediately after placement, while new bone formation simultaneously takes place.

Should one expect a different radiographic appearance with Bond Apatite®?

Due to the nature of the graft, the biphasic calcium sulfate matrix within the graft is simultaneously replaced by the patient’s bone; therefore, the radiographic appearance is completely different compared to other grafts, which always appear radiopaque due to their constant presence in the grafted site.

In contrast, the radiographic appearance with Bond Apatite® is as follows:

During day one after graft placement, it appears radiopaque.

Gradually, a radiolucent appearance takes its place (reflecting the graft's transformation into the newly-formed osteoid before its calcification).

Two to four weeks after graft placement, the majority of the grafted site appears radiolucent while few radiopaque spots remain, reflecting the presence of the HA particles. Within 12 weeks, radiopacity takes place with the appearance of the native trabecular form. This is the time when the new osteoid has already calcified.

Can Bond Apatite® be used for vertical augmentation?

There is no recommended specific protocol at this point for vertical augmentation.